An alternative design for the PCB was created. The PCB design files will need to be created on a different computer than on one of the student's because the version does not support the design of a board larger than 26mm x 17mm.
The primary assignment this week was preparing the presentation.
A spot welder for the battery pack is being searched for, or where the team can gain access to one.
Wednesday, February 26, 2020
Wednesday, February 19, 2020
29 Febuary 2020
This week, we recieved our litihum ion batteries and start building our cutom battery pack. The next step is to spot weld the batteries into the desirable configuration then start looking into wats to safely charge the battery pack. We were able to determine the open lab time for ME41 lab so we will be meeting there sometime this week to complete the custom battery pack done. We also spent today charging up some of the old universal batteries we had in the facility which we might use to help change our custom battery pack. We will make sure it is safe before using.
Wednesday, February 5, 2020
5 February 2020
Today we spent the majority of today looking for all the parts we need to build our power module. We were able to find a box for the housing of the power module on McMaster that will greatly reduce the overall cost of our project. We also went over the simulations we created last semester to double check all the equations to ensure everything was correct. We also started researching on the different switches we will be using on the power module to gain a better understanding on the fundamental functions of the components that will be making up the power module. All of this research will be used for our next presentation.
29 January 2020
The team met with Ron Swenson, Eric Hagstrom, and Dr. Furman to give an update on the status of the team's progress on the project. Today, the power module from the previous year was disassembled. The supercapacitors that are required for this year's design were taken out and set aside. The polarity of the supercapacitors was verified, as they were not specified on the datasheet, for BCAP0350 E270 T11. Now that the polarity is known, further progress on the design for the PCB can continue.
Wednesday, November 20, 2019
20 November 2019
This week, we are finalizing our design. We begin to figure out what components we need to run the system. We have added a fuse to make sure the current doesn't exceed a certain value. Also, we figure out how a relay works and uses them to control switching between each energy storage device. We will use a current sensor as an input to control the switching. Safety components such as diode and NPN transistor is also implemented.
We completed our battery calculation and decided to create a 3 series 2 parallel battery pack. The pack will have a capacity of 5Ah. We also purchased some components and will continue to do so as the week progresses. Lastly, we presented our project this week and the presentation is attached below.
Wednesday, November 13, 2019
13 November 2019
After attending Pod Car City, Eric was able to meet with Ed Porter, an attendee who is part of Santa Cruz PRT on Friday, November 8th. Mr. Porter possesses a guideway, bogie, controller, linear induction motor (LIM) that the Power Modules team can use. Mr. Porter was able to bring all these components except for the guideway on November 13th, Wednesday. The guideway will have to be transported to the Superway facility at a later date, which is still to be determined. Mr. Porter also has expressed a willingness to provide a DC to AC inverter and a phase inverter for the adaption of the DC power devices currently being used by Superway.
Time will need to be allocated to learning more about the LIM and how it is wired since there is limited documentation regarding this aspect from the motor's previous use. Along with the motor, the controller provided by Mr. Porter will also need to be familiarized. A block diagram of the components in the project, such as the charger, BMS, DC/DC converter, DC/AC inverter, 3-phase inverter, motor controller, and other components has been made.
For this coming week, work on the schematic for the PCB will continue, and preparation for the presentation and final report will commence.
Time will need to be allocated to learning more about the LIM and how it is wired since there is limited documentation regarding this aspect from the motor's previous use. Along with the motor, the controller provided by Mr. Porter will also need to be familiarized. A block diagram of the components in the project, such as the charger, BMS, DC/DC converter, DC/AC inverter, 3-phase inverter, motor controller, and other components has been made.
For this coming week, work on the schematic for the PCB will continue, and preparation for the presentation and final report will commence.
Wednesday, October 30, 2019
30 October 2019
We were able to meet with Dr. Ping Hsu earlier this week to discuss our current power module design. We were given the idea of incoporating DC/DC converters into our system to better regulate the current flow of the system. After discussing our finding to Dr. Furman, we later decided to use a DC/DC converter to charge the battery in our power module. Our supercapacitors will be used to slowly charge the battery pack in the system.
For the following week, we will try to meet with Dr. Saeid Bashash to furthur discuss our design and hopefully obtain answers to some of our current design. We have also decided who will be speaking at Podcar City event next week.
Subscribe to:
Posts (Atom)
15 April 2020
The team is discussing ethics. The group will begin working on the final report and the presentation.
-
This week, we recieved our litihum ion batteries and start building our cutom battery pack. The next step is to spot weld the batteries into...
-
The team is discussing ethics. The group will begin working on the final report and the presentation.
-
Today we spent the majority of today looking for all the parts we need to build our power module. We were able to find a box for the housing...